Built for thicker steel and longer shifts
The CUT 80 Heavy Cutter is a high output plasma cutting unit suited to workshop use where cutting jobs come in all day. It is made for fabricators, repair shops, fleet workshops and light manufacturing teams that need a machine they can use on a regular basis without constant adjustment.
For general cutting it handles mild steel, stainless steel and aluminium, with the best results coming from clean, dry air and the correct torch setup. The machine is a good fit when you want a practical cutter for brackets, frames, repair sections, gates, trailers and general steelwork in Vereeniging, Vanderbijlpark, Sasolburg and nearby industrial areas.
This model is also a solid choice for farmers and maintenance teams who need dependable cutting on site. It gives a cleaner edge than oxy fuel on many jobs and it is easier to move around the workshop or take out to site when needed.
Output, cutting range and model options
The CUT 80 range is suited to users who want more cutting capacity than a light duty machine can offer. Different packages are available depending on whether you need a handheld cutter for workshop work or a setup that can be tied into a CNC table. For many customers the key choice is between a standard manual torch set and a package prepared for machine cutting.
- Rated cutting output: 80 A class machine
- Typical clean cut thickness: up to about 20 mm on suitable steel
- Maximum severance thickness: up to about 30 mm depending on material and conditions
- Manual torch package for workshop and repair work
- CNC ready package for table use and guided cutting
- Suitable for intermittent or production use, depending on duty cycle and airflow
When you are ordering, it helps to think about the work you do most often. A workshop doing repairs and fabrication may want a handheld set with a longer torch lead, while a cutting table user will usually need a machine matched to the table size, torch mount and height control system.
Where the CUT 80 suits best
This cutter is well suited to fabrication shops, mechanical workshops, farming repairs, transport yards and general engineering businesses. It is often used for steel plate, profiles, pipe, brackets and damaged sections that need to be trimmed out and replaced.
It also suits operators who need a machine that can keep up with daily use in tougher conditions. In many parts of Gauteng and the Free State, dust, heat and load-shedding can all affect workshop work. A cutter like this is useful where you need quick setup, predictable cutting and less time spent waiting on gas bottles or pre-heating.
- Metal fabrication and repair work
- Automotive and fleet maintenance
- Trailer, gate and frame production
- Plant maintenance and breakdown work
- CNC table cutting for repeat parts
For coastal areas the machine should be kept in a dry store and checked often for corrosion on the torch consumables and earth connections. In busy inland workshops, regular cleaning goes a long way to keeping performance consistent.
Power, air and site setup
The CUT 80 needs a stable power supply and a clean compressed air line. For best results, the incoming power should match the machine specification and the workshop should allow for a proper outlet, earthing and breaker protection. If you plan to run it from a generator or during load-shedding, the generator must be sized correctly for the start-up and cutting load.
Air quality matters as much as power. Plasma cutting uses clean dry air, so the compressor should deliver enough pressure and flow for the torch to cut properly. Water, oil and dirt in the line will shorten consumable life and reduce cut quality, especially on thicker material.
- Stable supply voltage and correct earthing
- Dry compressed air at the required pressure
- Enough compressor flow for continuous cutting
- Space for torch leads, work clamp and safe fume extraction
- For CNC use, allow room for table alignment and cable routing
If the unit is going onto a CNC table, the torch height control and table earthing should be checked during installation. A tidy setup makes a big difference to cut consistency and helps reduce nozzle wear.
Care, servicing and consumables
Like any high output cutter, the CUT 80 performs best when it is kept clean and serviced on time. Consumables should be checked often because worn tips, nozzles and swirl rings can affect cut quality and increase running cost. If the air line is dirty or wet, those parts wear much faster.
Planned maintenance should include torch inspection, power source checks, internal cleaning, fan and airflow inspection, cable condition and earth lead condition. For CNC users, height control calibration and table servicing should also be part of the maintenance routine. This is the kind of care that keeps the machine earning its keep instead of standing idle.
- Torch Repairs
- Power Source Repairs
- Preventive Maintenance
- Consumables Checks
- Air System Inspection
- CNC Table Servicing and Height Control Calibration
We also handle on site breakdowns, machine commissioning, operator training and spares supply, which is useful when a workshop cannot afford long down time. A quick check from an experienced technician can often identify whether the issue is airflow, power, torch wear or a setup problem.
What to check before you order
Before you place an order, it helps to have the material thickness, cutting volume and intended use in mind. That makes it easier to choose the right torch package and avoid buying a machine that is too light for the job or more machine than you need.
Consider whether the cutter will be used mainly by one operator or shared across a workshop. Also check whether you need a handheld unit, a CNC ready setup or both. If the machine is for daily production work, ask about duty cycle, air requirements and the type of consumables supplied with the package.
- Main material type and thickness
- Manual or CNC use
- Power supply available on site
- Compressor size and air quality
- Required torch lead length
- Training and commissioning needs
Our Vereeniging base supports customers across Gauteng and the Free State, including Alberton, Germiston, Meyerton, Bloemfontein and Welkom. If you need a practical cutter with local support and proper follow through, the CUT 80 Heavy Cutter is a strong fit for day to day workshop use.
Key facts
| Rated output | 80 A class plasma cutter |
|---|---|
| Input power | Industrial AC supply, matched to installation |
| Cut thickness | Clean cuts up to about 20 mm |
| Severance thickness | Up to about 30 mm depending on material |
| Torch options | Handheld torch or CNC ready package |
| Air requirement | Clean, dry compressed air with correct flow and pressure |
